DISCOVERING PLUMBING BASICS IS ESSENTIAL WHEN INSTALLING A BATHTUB

Discovering Plumbing Basics is Essential When Installing a Bathtub

Discovering Plumbing Basics is Essential When Installing a Bathtub

Blog Article

Call

Just about everyone has their personal piece of advice involving Tools You Need to Install a New Bathtub .


How to Install a Bathtub
Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is also a moderately hard project. If the old tub is readily accessible, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either case, the job is within a house handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the new one. Ensure you have qualified on your own for the work as well as are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed job, it is better to consider employing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This post will aid you set up a new bath tub in your shower room if you have already purchased a new bathtub and also do not need to alter the arrangement of your previous supply of water pipes.
Your tools and product list should consist of the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installation


    First of all, the supporting framework supplied with the bath must be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps device to prevent pressure on the tub.
    Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the supplied washers.
    Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, then the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted access that is frequently the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipelines have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
    Before moving on to fit the new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.

    Setting up the Bath tub


    Making use of the two wooden boards under its feet, position the bathtub in the required placement. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny points.
    The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bath tub until the level checks out degree.
    To mount taps, fit the bottom of the outermost flexible tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
    Turn on the water supply and also check all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub and also check the overflow electrical outlet and the regular electrical outlet for leakages.
    Ultimately, fix the bath paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub needs to wait till the bathtub has been made use of at the very least once as this will certainly settle it right into its last setting.

    Suitable New Taps


    If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipelines.
    If you need to fit a monobloc, then you will call for lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former kind must be connected to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom and the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
    You can select from a range of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this activity before sealing.
    Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is a good idea to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    I was introduced to that editorial about Tools You Need to Install a New Bathtub through a friend on a different blog. Don't hesitate to set aside a second to share this content if you enjoyed reading it. Many thanks for your time invested reading it.


    Call Us Today

    Report this page